I mounted my Alexloop to a picnic table and fired up my trusty KX3. Things got off to a slow start but I eventually connected with fellow SKCCer, K9FW, on 30M. Al always puts out a great signal from Indiana. The 40M band was tied up with Ohio QSO Party stations. I worked a few of them before loading up the bike to continue my ride.
There was nothing earth-shattering, radio-wise, but it was a beautiful day to be out cruising on my bike. I’ll take those mid-70s temperatures any day.
I was still recovering from a long drive home yesterday but I wanted to get out for this year’s Skeeter Hunt contest. It was a lot of fun and I’m glad I managed to catch part of it.
I found a parking spot near a picnic table in an almost deserted area of the Park. The temperature was in the 90s today, so I made sure to pick a table under a shady tree. I mounted my 19-foot homebrew vertical on the truck and ran a coax cable over to the picnic table. I fired up my KX3 just after the contest started.
My set up in Valley Forge Park for the 2019 Skeeter Hunt. The table was well-shaded and close enough to the truck for 18-feet of coax to reach the antenna.
There was quite a bit of activity on 40M, so I spent most of my time there. When things started to thin out on 40M, I changed bands and picked up 3 more skeeters on 20M.
WB3GCK hunting skeeters in Valley Forge National Historical Park
I packed up after an hour and a half but it was a fun time. I ended up with 22 QSOs in the log, including 19 skeeters and 14 SPCs. As always, it was nice to work some familiar callsigns.
Thanks to Larry W2LJ and the NJ QRP Club for sponsoring this contest. It continues to be one of my favorite QRP events of the year.
Once again, my family made our annual vacation trip to North Carolina. We rented a house in Corolla on the Outer Banks for the week. Of course, in between the usual vacation activities, there was some ham radio involved.
For various logistical and traffic reasons, it took us longer than usual to get there. It wasn’t until the next day (Sunday), that I was able to get an antenna up. This year, I went with my trusty “Up & Outer” antenna.
I mounted a 28-foot pole on the 3rd story deck for the vertical element. I strapped a smaller pole to a fence to support the horizontal element. I put a BNC-to-binding post adapter on my KX3 and fed the 300-ohm twin-lead directly. It loaded up fine from 60M through 10M. Surprisingly, the ambient noise levels were low. Man-made noise is usually a challenge in these rental houses.
Poles supporting my “Up & Outer” antenna. The pole on the left is supporting the vertical wire. The pole on the right is the end support for the horizontal wire.
I operated from a 2nd-floor deck on the rear of the house. This spot provided some nice shade for most of the day and gave a great view of Currituck Sound.
My outdoor shack for the week. The chair was particularly comfortable and the view of Currituck Sound was great.
I managed to catch a few hours of the SKCC Weekend Sprintathon (WES) contest. Running 10 watts, I worked 20 stations and added 8 more new contacts to my quest for the Senator Award. For good measure, I also worked DP6A in Germany who was participating in another contest. So, the antenna set-up appeared to be working fine.
The view of Currituck Sound from my antenna.
For the rest of the week, I fell into a pattern of casual QRP operating for a bit in the late mornings. The rest of the time was spent swimming, crabbing, and riding bikes with my grandkids. I still managed to make a handful of contacts each day and enjoyed some nice rag-chews.
Mid-week, we had some unsettled weather. I had a “Plan B” for inclement weather, though. I planned to move my radio gear into an unused sitting area not far from my outdoor location. I was going to use a small piece of pipe insulation to route the twin-lead in through a sliding door and keep it from touching the metal door jamb. Fortunately, the weather cooperated and “Plan B” never came into play.
As usual, the week went by too fast. On our last day, I made two more contacts before it was time to pack up the radio and tear down my antenna.
This was another fun vacation, radio-wise. I made 40 contacts, including some very nice early morning CW chats. I also worked a couple of stations who were also operating portable while on vacation and made a couple of DX contacts to boot. Plus, I continued my slow-but-steady progress towards my SKCC Senator Award, adding 16 new ones this week.
It was nice to be using a decent antenna in a low-noise environment — a welcomed change of pace from my home station!
We’re in the midst of a busy camping season. Over the past weekend, we took our little “QRP” camper to Codorus State Park. I didn’t spend too much time on the radio this weekend but I did have some fun on 30M.
Codorus State Park, in southern York County, is one of our favorites. We try to get out there at least once a year. It’s a large, scenic park and includes and encompasses 1,275 acre Lake Marburg. Our site this time was large and wooded, with no neighbors on one side.
It was getting towards dark when I finally got around to putting up an antenna. I had a nice contact with W2IFB on 40M who was putting out a great 3-watt signal from New York. Assured that everything was in order, I headed out to join my (far) better half at the campfire.
The next morning, I made a few more contacts on 40M and 80M. Among those was N2KMF who was operating portable from Crandall Park near Glen Falls, New York.
WB3GCK operating at Codorus State Park near Hanover, Pennsylvania
For the rest of the weekend, I stayed on 30M, which provided lots of activity. The 30M band has always been one of my favorites and there was ample activity there. There weren’t any exotic contacts but I had fun working stations up and down the East Coast and out to the mid-West.
There was some deep fading on 30M on Saturday but Sunday was a different story. I got on around mid-day briefly before heading out for the trip back home. I was met with a mini pile-up and the signals were all solid. I quickly worked four stations before packing up the radio and tearing down the antenna.
Scenic Lake Marburg in Codorus State Park
The good news is that I made some more progress towards my SKCC Senator award. The bad news, though, is that I had to miss this year’s running of the Flight of the Bumblebees. The QRP contest coincided with our drive home. I hope all of the bumblebees had fun and I hope to be able to join in the fun next year.
My (far) better half and I took our little camper to one of our favorite campgrounds for the weekend. Our destination was Cunningham Falls State Park in north-central Maryland. Our trip coincided with the Straight Key Century Club’s (SKCC) monthly Weekend Sprintathon (WES). So, I spent most of my ham radio time operating in the contest.
Our site was wooded and nicely shaded but not large enough for the larger antenna I planned to use. Instead, I strapped my Jackite pole to a lantern post and used my trusty 29.5-foot wire and 9:1 unun.
I got on the air on Saturday at 1200Z when the contest started. The noise from my trailer was very low (for reasons unknown) and I heard some strong signals on 40M. Things got off to a good start but got a bit more challenging as the day went on.
I worked the contest on and off over the weekend with mixed results. I was able to easily make some contacts while others were difficult, if not impossible. Cunningham Falls is located in a very mountainous area. That, coupled with some sketchy band conditions, made it an interesting weekend.
I’ve been working towards my SKCC Senator award but I’ve been in a bit of a slump the past few weeks. I decided to increase my KX3’s power to a whopping 10W to improve my odds. This was the first time I haven’t been in the QRP category for a WES contest.
WB3GCK working hard (or hardly working) during the SKCC WES contest from Cunningham Falls State Park in Maryland
Despite the terrain and propagation issues, my casual operating resulted in 28 contacts in my log. Most were on 40M with a couple on 80M.
Here are the highlights:
I managed to add 12 more QSOs toward my Senator award. I only have 65 more to go.
On Saturday evening, I heard R7DA calling “CQ WES” from Russia on 40M. I gave him a call and got a “WB3? AGN.” It took quite a few tries before he had my full callsign and we were able to complete the QSO. Alex deserves major props for his patience and persistence in pulling my puny 10W signal out of the noise.
On Sunday morning, I got on the radio for a few final contacts before packing up. As I was tuning around looking for WES stations, I found N4ZN doing a Parks on the Air (POTA) activation in New York. I gave him a call and had a park-to-park QSO. After that, I pulled the plug and started packing up for the long drive home.
Despite the occasional frustrations, it was an enjoyable weekend of camping and ham radio.
I spent the weekend camping in one of the most scenic campsites we’ve encountered in a while. Unfortunately, it wasn’t a great weekend for weather-wise and radio-wise.
The park in question was Elk Neck State Park in northeastern Maryland. Our site was wooded, shady, and had a beautiful view of the Elk River.
We rolled in on Friday evening just before dark. We went about setting up the camper and I set up my usual 29.5-foot vertical. I checked to make sure the radio was working and headed out to join my (far) better half at the campfire.
The next morning was another hot and humid day, with temperatures headed towards the 90s. We’ve had a bunch of those lately. I set up the KX3 in a shady spot and checked around on 40M for some SKCC contacts. I worked a station in Georgia but it was a bit of a struggle. Although the propagation forecasts looked pretty decent, there was some deep fading and lots of static crashes.
WB3GCK operating outside the camper at Elk Neck State Park in Maryland
After breakfast, I tried again. After going unheard by several stations, I finally got through to a station in New Hampshire. Again, it was a struggle to complete the contact (mostly for the other guy, I suppose).
Around this time, it started raining. A spotty but severe thunderstorm was headed right towards us. We quickly stashed our outdoor gear and retreated into the trailer. It poured buckets. After the storm passed, I found my coax submerged in a puddle. (Note to Self: Test that coax to make sure it’s OK.)
The aftermath of one of the storms that rolled through Elk Neck State Park. My coax cable resembled the Transaltlantic Cable.
It rained on and off for much of the afternoon. With thunder and lightning in the area, I stayed off the radio. Fortunately, the rain stopped long enough for us to make dinner outdoors and enjoy another campfire. After we turned in for the night, yet another storm came through. This one featured lots of thunder and lightning.
This morning, I set up the radio outside again. It was another hot and humid day. The biting flies were out in full force, too. Despite all that, I fired up the radio. I made one last contact with another station in New Hampshire. As you might guess, the op on the other struggle to get my information. His QRO signal was fading, so I can image what I must have sounded like on his end. After that, we decided to pack up the camper and head home.
The view of Elk River in Maryland. There were some great sunrises over the river but, unfortunately, I couldn’t capture a decent picture.
I was a little disappointed that I was only able to squeeze out 3 contacts over the weekend. I would much rather write a post a making a bazillion contacts to far-flung places. I know these are tough times for QRP but still…
Elk Neck is one of my favorite campgrounds, so I’d like to get back down there in the Fall. Hopefully, the weather, propagation, and bugs will be better then.
Well, another Boschveldt QRP Club Field Day is in the books. We had a much smaller crew this year but a good time was had by all.
Once again, we were graciously hosted by a local businessman who allowed us to use his private property. Pennsylvania has had a lot of rain lately, so parts of our Field Day site were soggy, to say the least. (My poor truck needs a bath!) We adapted nicely, keeping our equipment on the higher parts of the property.
This year, we ran 2A (QRP and battery-powered) in the Eastern Pennsylvania section. We used the club’s callsign, W3BQC. A few of our regular attendees had other obligations this year. So, this was a scaled-back Field Day for us. The main participants were Ed K3YTR, Ed WA3WSJ and me. On Saturday, Paul KB3ZOH and Diane KC3AOA stopped by for a visit.
I operated CW on 40M and below from my tent. I was running my KX3 at 5 watts with a 53-foot inverted L antenna fed through a 9:1 unun. I used a tree to secure the far end of the horizontal part of the antenna. It only took me 3 tries to hit my target branch. That’s pretty good for me.
WB3GCK – running CW from my tent
WA3WSJ operated CW on 20M and above using a minimalist set up under an umbrella. He was running his KX2 into a 50-foot inverted L. He also camped out in his hammock under a tarp.
WA3WSJ operating CW with his minimalist setup
K3YTR worked SSB on 6M, 2M and 440 from his car and slept in a slick little teardrop camper. We used the trailer’s rear kitchen for our cooking.
The kitchen area of K3YTR’s teardrop camper
On the air, the bands were up and down. WA3WSJ and I both noted some deep fading on the HF bands. Nonetheless, we had no trouble making contacts. I had good luck on 40M, working stations all over the East Coast and out to the mid-West. WA3WSJ was working stations coast-to-coast, including the U.S. Virgin Islands. K3YTR, unfortunately, was plagued with equipment problems, so he didn’t have much luck on the VHF/UHF bands.
K3YTR setting up his VHF/UHF antennas
As always, the Boschveldt crew takes a lot of breaks for food and socializing. After dark, we gather around the campfire to roast marshmallow Peeps® and swap tall tales. We definitely are not hardcore contesters.
As always, no records were broken over the weekend. Still, it’s always a good time when our little band of QRPers gets together.
This weekend is the SKCC‘s monthly Weekend Sprintathon (WES) contest. When I can, I like to go out and operate portable for at least part of the contest. I headed to Valley Forge National Historical Park for a couple of hours to take advantage of the great weather.
On arrival, I headed for a shady spot that I’ve used a few times before. I mounted my 19-foot vertical on the back of my truck and set up a small table behind my truck. I fired up my KX3 and got on the air.
My set up in Valley Forge
In short order, I logged several stations on 40M, including a POTA park-to-park QSO. (Valley Forge is POTA/WWFF K/KFF-0761.) Moving up to 20M, I made a few more contacts.
I decided to check 15M and I’m glad I did. I found several very strong stations who easily heard my meager 5-watt signal. I called CQ for a while and picked up a few more stations. I seemed to have a pipeline to Indiana and Illinois. It was great to hear some WES activity on 15M.
After a couple of hours, I started to run out of shade. I was getting hot and so was the KX3. I decided to pack up for the day. Besides, I had to do some preparations for a public service event early the next morning.
It was a great day for portable operating and I added a few more QSOs towards my SKCC Senator award.
As part of my recent emphasis on exploring local trails, I did some hiking on a great little trail today. This gem of a trail has become my favorite local trail for a quick getaway.
The Neal Thorpe Trail begins at the Schuylkill Canal Park in Mont Clare, Pennsylvania. The trail is named in honor of the late founder of the Schuylkill Canal Association. It’s not a very long trail; it’s less than a mile in length. The scenery, though, is outstanding. Even though I was just across the river from the weekend hustle and bustle of downtown Phoenixville, I felt like I was out in the middle of nowhere.
Entrance to the Neal Thorpe Trail near the Schuylkill Canal Lock 60
From the trailhead, the trail passes through a ravine and parallels a small creek. According to an online description of the trail, it eventually turns left and heads up a steep climb. The problem, I found, is that there are lots of side trails and no trail markings.
Neal Thorpe Trail. The beginning of the trail follows a small creek through a scenic ravine.
At one point the trail crossed the creek and I found a trail heading off to the left up to the top of the ridge. It wasn’t marked but I went ahead and made the climb anyway. When I got to the top, I found no less than 4 trail options. Of course, none were marked. I continued on the trail straight ahead.
I headed down the trail a bit and decided to stop and set up my radio gear. I found a log about 20 yards off the trail, which I used for my operating position. I set up my portable vertical about 15 feet behind me.
WB3GCK sitting like a bump on a log along the Neal Thorpe Trail
Band conditions weren’t the best. There was a fair amount of fading and some static from storms heading in. Nonetheless, I worked a few Museum Ships Weekend (MSW) stations. They were all in Massachusetts, as it turns out. I also had an SKCC QSO with a station in North Carolina before packing up.
The hike back down into the ravine was a little tricky but uneventful. I took my time hiking back to enjoy the surroundings.
The Canal Park was busy with lots of people canoeing, kayaking, and just enjoying the beautiful weather. I found it interesting that, with all that activity in the park, I pretty much had the trail to myself. I briefly saw one other hiker off in the distance but that was it.
With the lack of trail markings, I’m still not sure if I was on the right trail or not. It doesn’t matter though; I found a great new place to operate out in the woods. And, it’s only minutes from home.
Here’s yet another quick little hack. I raided my junk box to cobble together a ground mount for my portable vertical. While this solved a couple of specific issues I had, it might only be of interest to a few of you folks out there.
I often support my 19-foot vertical with one of those inexpensive fishing poles from eBay. (I paid around $10 USD for my 7.2M pole.) I had been using a simple method for ground mounting. I shove a screwdriver in the ground, take the bottom cap off of the pole, and place the pole over the screwdriver. Voila!
While the screwdriver technique is a useful way to support my vertical, there are two issues with it. First, the screwdriver method places the bottom of the pole in direct contact with the dirt. This can gunk up the threads on the bottom of the pole. (Ask me how I know.) Next, since my homebrew 19-foot vertical takes up the entire length of the pole, the matchbox ends up too close to the ground for my liking. I made a simple little gizmo that addresses both of these issues.
Antenna ground mount in use with my 19-foot vertical
From some scraps and junk I had on hand, I used the following:
Duct tape (optional, for a better fit between the 1/2-inch PVC and the bottom of the pole)
A dab of Lock-Tite thread locker
[Note: The PVC pipe I used works with the particular pole I use. If the bottom of your pole has a different inside diameter, you might need to use a different size pipe.]
I joined the two pieces of PVC pipe together with the PVC reducer. Then I glued the two end caps together, back-to-back. Next, I drilled a 1/4-inch hole through the center of the two end caps. I fastened the stainless steel rod with two nuts and a lock washer. I also used a dab of thread locker for good measure. I had to do some sanding on the 3/4-inch pipe to allow the end caps to slide on and off easier. At this point, you might want to put a layer or two of duct tape on the 1/2-inch pipe for a snug fit inside the pole.
The two main assemblies of the antenna ground mountStainless steel rod bolted through the two back-to-back PVC end caps
In the field, I place the end cap assembly on the 3/4-inch pipe and shove the rod into the ground. The pole goes over the 1/2-inch PVC pipe, of course. This places the bottom of the pole about 8 inches above the ground. With lightweight poles, guying is unnecessary. For travel, I flip the end cap assembly around so that the bolt stores inside the pipe. This prevents poking holes in my backpack or bicycle pannier bags.
Antenna ground mount assembled for useAntenna ground mount configured for travel. The stainless steel rod is stored safely inside the PVC pipe assembly.
The threads on the end of the stainless steel rod pick up some dirt in use. It’s not a major problem but I might cut the rod off just above the threads. I haven’t decided yet.
That’s all there is to it. I’m hoping the accompanying pictures clarify how I built it.
WB3GCK QRP Amateur Radio 